About our 3.9-Watt LED Dimmable Indoor-Outdoor Step Lights, Rectangular Scoop
Featuring a sleek profile and no visible hardware, these step lights seamlessly blend into any architecture. These energy-efficient step lights illuminate paths, hallways or walkways in a bright, warm white light with little or no glare. They are easy to install and are available in four attractive finishes.
- 4 Finishes:
Brushed Nickel (PWL-LED100-CBN)
Stainless Steel (PWL-LED100-CSS)
- Durable Construction: 316 cast stainless steel for stainless steel finish; die-cast aluminum for all other finishes
- LED module
- Wattage: only 3.9 watts
- Line Voltage: 120 volts
- Light Output: 68 lumens
- Good Color Rendering: 83 CRI
- Warm White Light: color temperature of 3000K (warm white)
- Very Long Life: 40,000 hours of rated life on average
- Easy to Install: easily installs in a 2in x 4in junction box with minimum inside dimensions of 2in(H) x 2in(W) x 3in(L) (purchased separately - generally found in most electrical supply stores). Direct wiring, no driver needed. Please refer to these Installation Instructions (PDF).
- Mounting Accessories Included: mounting bracket, gasket, screws, and rubber washers included
- Junction Box Sold Separately: a single gang junction box is required for installation and is not included. It can be found in most local electrical supply stores. We are unable to provide a single gang junction box that meets all local electrical codes and we suggest checking local electrical codes and the National Electrical Code (NEC) before installing these step lights. It is also wise to consult with a licensed electrician in your geographical area about any electrical details that you might have questions about and to make certain that you are satisfying all of the appropriate electrical codes.
- Dimmable: yes, may be dimmed with an electronic low voltage (ELV) dimmer.
- Max Run: up to 200 fixtures can be connected in parallel
- Lead Wires: black (hot), white (neutral), and green (ground)
- Outdoor or Indoor Use: IP66 rating (totally protected against dust and protected against temporary flooding of water)
- Large Quantity Discount: If you would like us to quote on a large quantity of 3.9-Watt 120-Volt LED Indoor-Outdoor Step Lights, please call us at our toll-free number or use the online Quotation Request for Large Quantities form. We are always happy to provide you with our best large quantity pricing.
3.9-Watt LED Dimmable Indoor-Outdoor Step Lights, Rectangular Scoop
By Mike from Aspen on October 18, 2013
Does this mount on a standard single gang box?
By Jacob from Pegasus Lighting on October 18, 2013
It installs in a 2in x 4in junction box with minimum inside dimensions of 2in(H) x 2in(W) x 3in(L).
By Jim from Ocean City, NJ on May 11, 2014
I purchased six of the above step lights. The instructions for this light indicate to use an Electronic Low Voltage Dimmer (ELV). What dimmer should be used? The dimmer would be connected to 120 line voltage, not a 12-24V transformer. I'm confused as to which dimmer to use. Thank you.
By Jacob from Pegasus Lighting on May 12, 2014
Answer:Jim, you need to use an ELV dimmer - http://www.pegasuslighting.com/electronic-low-voltage-dimmers.html
The dimmer will connect to your line voltage and then in turn connect to the light fixtures.
The step light has a built in driver (similar to a transformer) and WAC Lighting, the manufacturer, recommends dimming with ELV dimmers.
By Francis Robin from Hollywood, Florida on November 5, 2013
How many of these lights is minimally required if I still want them to be dimmable? Thank you.
By Jacob from Pegasus Lighting on November 7, 2013
For best dimming performance, you'll need to meet the dimmer's minimum wattage requirement. For example, if the dimmer requires a minimum load of 30W, then you would need to connect 8 step lights to the dimmer.
By Peter from Portland on July 9, 2014
If I need only 7 of this lights how do you recommend to dim them?
By Jacob from Pegasus Lighting on July 9, 2014
Answer:Peter, I spoke with WAC Lighting, the manufacturer, about the dimming and minimum load issue.
In general, Lutron's ELV dimmers require a min load of 40W.
If you do not meet that load requirement, WAC suggests using Lutron's Skylark SELV-300P - http://www.pegasuslighting.com/skylark-dimmer-electronic-transformer.html
WAC has tested this specific dimmer with a single step light and found it dims from 100-10% without issue.
Since you intend to install 7 step lights, which is below the 40W min load, I would advise using the Skylark dimmer. I hope this helps!
By James from Ocean City, NJ on July 10, 2014
Answer:You can use any low voltage digital dimmer, from a simple model to an expensive one with lights and touch plates. Digital low voltage, not mechanical. I used Lutron SELV-300P-WH low voltage single pole dimmer. It has an on-off switch and a bar for the dimming. It can be used to dim many more lights then you have.